Bending Copper and Brass: Work Hardening, Radius and Annealing
Copper and brass are soft, highly ductile, and among the easiest metals to form, until work hardening sets in. Bend them cold and the bend zone gets stronger and more brittle, so a second hit behaves differently and over-working cracks the metal.
Copper and brass bend easily, then work-harden
Copper and its zinc alloy, brass, are soft, highly ductile, and among the easiest metals to form by hand or machine. The catch is work hardening: bend them cold and the bend zone gets stronger and less ductile, so a second hit or a re-bend behaves differently, and over-working cracks the material. They also scratch and show tool marks readily, and copper can develop a surface that reads as a defect even when it is harmless.
Common grades
- C110 (electrolytic tough pitch copper). Very ductile, used for busbars, roofing, decorative work.
- C260 / C272 (cartridge and common brass). Good formability, used for enclosures, fittings, trim.
- Phosphor bronze and beryllium copper. Springy, higher strength, work-harden aggressively, need care.
Springback and radius
As soft metals, copper and brass have low yield, so springback is small for the soft tempers, like mild steel. The practical minimum radius is often near the material thickness. The variable is work hardening: as you form, the local hardness climbs, so hold the bend in one hit where possible rather than repeatedly nudging it. If a part needs several bends, sequence them so you are not re-working the same zone.
Annealing when work hardening bites
When a part demands a tight radius on a grade that has work-hardened, or multiple severe bends, an intermediate anneal restores ductility. This is normal practice for copper and bronze spring parts. It is a process step, not a failure; plan for it rather than fighting cracking.
Surface and tooling
Both metals scratch and pick up tool marks, and copper in particular can bruise. Use clean, smooth tooling and consider a protective film on the visible face. Keep steel fines off the dies so they do not embed in the soft metal. The tooling guidecovers die selection for soft, surface-sensitive metals.
Tonnage and flat pattern
Copper and brass need roughly half the tonnage of mild steel at the same thickness. Plan the flat pattern with the bend allowance calculator; the K-factor sits in the usual 0.3 to 0.4 range for air bending, measured on your actual temper.
Questions we get asked
Is copper easier or harder to bend than steel?
Easier in terms of force: copper needs roughly half the tonnage of mild steel and tolerates a tight radius. The complication is work hardening. Bending cold strengthens the bend zone, so repeated hits behave differently and over-working cracks the metal. Plan to form in as few operations as possible and anneal if needed.
Why does my brass part crack after several bends?
Work hardening. Each cold bend raises the local strength and lowers ductility, and a re-hit on the same zone eventually cracks it. Form each bend in one operation where you can, sequence bends to avoid re-working a zone, and anneal between severe operations on springy grades like phosphor bronze.
How much tonnage do copper and brass need?
Roughly half of what mild steel needs at the same thickness because of the low yield strength. The real constraints are surface finish and work hardening, not force.
How do I keep copper and brass scratch-free?
Use clean, smooth, preferably polished tooling, keep steel fines off the dies, and apply a protective film to the visible face for finished parts. Copper bruises easily, so avoid dragging it across rough surfaces.
What K-factor should I use for copper and brass?
For air bending, a K-factor in the 0.3 to 0.4 range is a reasonable start, but measure it on a sample of your actual temper and feed it to the bend allowance calculator, because tempers vary.
Still not sure what your power will support?
Tell us your supply voltage, available breaker size and the thickest material you need to bend. We will tell you straight whether single phase will do it.